17.3 Configuring Sequence Mode
Sequence mode cycles through connected channels to give you an overview of what is happening on all cameras. You can customize the order
that channels appear in Sequence mode, as well as configure which viewing modes should be used.
To configure Sequence mode:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click DISPLAY, then click the Sequence tab on the side panel.
-
Choose how many channels will appear on screen when Sequence mode is triggered by motion detection (you must check Sequence when configuring motion detection — see
12 Motion Detection
for details).
-
Enter the amount of time in seconds that each channel or page will appear on screen during Sequence mode.
-
Select a viewing mode to configure. It is recommended to start with View 1 and make your way to View 9. By default, all viewing modes are included in the Sequence mode cycle.
-
Configure the order of channels shown on screen for each viewing mode. Uncheck channels / channel groups that you want to
remove from the Sequence mode cycle.
-
Click Apply.
17.4 Camera Menu
The Camera Menu allows you to manage IP cameras, set recording parameters, and assign custom titles for your cameras.
17.4.1 Viewing Camera Status
View the connection and alarm status for all connected cameras.
To view camera status:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click CAMERA, then click Registration on the side panel. Click the Status tab on the top panel.
17.4.2 Camera Firmware Versions
View firmware versions for connected cameras.
To view camera firmware versions:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click CAMERA, then click Registration from the side panel. Click the Firmware tab on the top panel.
17.4.3 Upgrading Camera Firmware
You can update the firmware for connected IP cameras through the NVR. Firmware upgrades provide enhanced functionality for
the cameras. Typically, a camera firmware upgrade will not be necessary unless directed to do so by technical support.
To upgrade the camera firmware:
-
Download the camera firmware file.
|
Note
|
Make sure that the firmware file you are using is compatible with your IP camera model.
|
-
Extract the firmware file and copy it to a USB thumb drive (not included).
-
Insert the USB thumb drive (not included) into a USB port on the system.
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click CAMERA, then click Registration on the side panel. Click the Upgrade tab on the top panel.
-
Click Select. Select the firmware file on the USB drive and click OK.
-
Check the cameras you would like to apply the upgrade to in the list and then click USB Upgrade.
|
CAUTION
|
Wait for the firmware upgrade to complete before turning off or unplugging the cameras or NVR. The cameras will restart during
the firmware update process.
|
17.4.4 Configuring Video Overlay Settings
The Overlay tab allows you to configure the text and information that appears overtop of the camera image, such as time and
channel display.
To configure video overlay settings:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click CAMERA. Click the Overlay tab on the side panel, then click the Overlay tab on the top panel.
-
Under Channel, select the camera you would like to configure.
-
Configure the following settings:
-
Time Display: Check to display the time information during live view. Click to choose the position of the time display overlay. Click-and-drag
the time display to reposition it. Right-click when finished.
-
Channel Name: Check to display the channel name. Enter the camera’s name and click to choose the position of the channel name overlay.
Click-and-drag the channel name to reposition it. Right-click when finished.
-
Click Apply to save changes.
-
(Optional) Click Copy to copy overlay settings to other channels.
17.4.5 Configuring Privacy Masking
The Privacy Masking tab allows you to block certain areas in the camera’s field of view when recording (Masking).
To configure privacy masking settings:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click CAMERA. Click the Overlay tab on the side panel, then click the Privacy Masking tab on the top panel.
-
Under Channel, select the camera you would like to configure.
-
Check Preview or Record. Preview means the privacy mask zone(s) cannot be viewed when the system is in preview status. Record means the privacy mask
zone(s) cannot be viewed when the system is in recording status.
-
Select 1 to 4 privacy masking zones on each channel. To set the size of the zone(s) click and drag the outer white line around
the box.
-
Click Apply to save changes.
-
(Optional) Click Copy to copy privacy masking settings to other channels.
17.4.6 Configuring Snapshot Recording Settings
The system can be set to record snapshot images when a camera detects motion. These snapshots can be viewed through the Playback
menu or can be attached to email alerts and push notifications. Use the following procedure to set the snapshot parameters
for each camera.
|
Note
|
Snapshot recording must be enabled for motion detection in the Event menu. See
12 Motion Detection
for details.
|
To configure snapshot recording settings:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click CAMERA, then click theRecording tab on the side panel. Click the Snapshot tab on the top panel.
-
Under Snapshot, select the number of snapshots the system will take when the snapshot button is pressed.
-
Configure the following settings for snapshots saved automatically from motion detection or the snapshot schedule:
-
Channel: Select the channel you would like to configure.
-
Mode: Select Timing for the system to take snapshots at fixed intervals throughout the day, or select Trigger for the system to take snapshots only when triggered by motion detection (snapshot recording must be enabled in the motion
detection menu - see
12 Motion Detection
for details).
-
Image Size: The image size is the same as the Main Stream resolution of the camera.
-
Image Quality: Select the snapshot image quality between 1 (lowest) and 6 (highest)
-
Snapshot Frequency: Enter the time between snapshots in seconds.
-
Click Apply to save changes.
17.4.7 Creating Custom Channel Names
You can assign custom names to your cameras. For example, you can name your cameras based on their location (e.g. hallway
or front door).
To create custom channel names:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click CAMERA, then click the Channel Name tab on the side panel.
-
Click a channel to enter a custom name.
-
Click Apply to save changes.
17.5 Information Menu
View system information related to storage, network status, system warnings, and more.
17.5.1 Version Information
View system information such as device ID, model number, IP address, and firmware version.
To access the Version Info menu:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click INFORMATION, then click the Information tab on the side panel. Click the Version tab on the top panel.
17.5.2 Hard Drive Information
View information related to the hard drives installed in the system, including capacity, status, and type.
To access HDD Info:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click INFORMATION, then click the Information tab on the side panel. Click the HDD Info tab on the top panel.
17.5.3 BPS
Shows bitrates of connected cameras. The bitrate is the amount of data the camera is sending to the system.
To access the BPS menu:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click INFORMATION, then click the Information tab on the side panel. Click the BPS tab on the top panel.
17.5.4 System Log
Search for system logs in a certain time range.
To access the log menu:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click INFORMATION, then click the Log tab on the side panel.
17.5.5 Alarm
View a summary of active system alarms. Activated alarms are highlighted in white. Additional info such as channels that are
currently detecting motion is shown.
To access Alarm Status:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click INFORMATION, then click the Alarm tab on the side panel.
17.5.6 Online Users
View all users connected to the system using computers or mobile devices.
To access the online users menu:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click INFORMATON, then click the Network tab on the side panel. Click the Online Users tab on the top panel.
17.5.7 Network Load
View network traffic your system is sending and receiving.
To access the network load menu:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click INFORMATION, then click the Network tab on the side panel. Click the Net Load tab on the top panel.
17.5.8 Network Test
Test if your system can connect to other devices over the LAN or Internet. You can enter the IP address of a device and click
Test to determine if your system can connect to it.
To access the network test menu:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click INFORMATION, then click the Network tab on the side panel. Click the Network Test tab on the top panel.
17.5.9 Saving Your System Configuration to a USB Thumb Drive
The system allows you to save your current system configuration to a USB thumb drive (not included). This is useful if you
want to backup your current settings.
|
Note
|
This function only saves settings created in system menus. It does not save or backup any video.
|
To save your system configuration to a USB thumb drive:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click INFORMATION. Click theUpdate/Reset on the side panel, then click the Config Backup tab on the top panel.
-
Under Device Model, select the USB device where you would like to save the configuration.
-
Click EXPORT to save your current system configuration.
To restore a saved system configuration:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click INFORMATION. Click the Update/Reset tab on the side panel, then click the Config Backup tab on the top panel.
-
Under Device Model, select the USB device where the system configuration is saved.
-
Click the folder with the configuration file you would like to restore. Configuration file folders are labeled “Config” and
then the time and date the configuration was saved (e.g., Config_20140425103727).
-
Click Import to restore the system configuration.
-
Click OK to confirm. The system will restart to complete the operation.
17.5.10 Restore Default Settings
Restore the system to its default settings.
To restore default settings:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click INFORMATION. Click the Update/Reset tab on the side panel, then click the Default tab on the top panel.
-
Check the menus you would like to reset to default settings.
-
Click Apply.
17.5.11 Upgrading Firmware Manually
The primary method for upgrading system firmware is automatically over the Internet. The system also supports firmware upgrades
from a USB thumb drive (not included).
Prerequisite:
-
Save the .bin firmware file for your unit onto a USB flash drive (not included), and connect the drive to one of the system’s free USB ports.
To upgrade firmware manually:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click INFORMATION. Click the Update/Reset tab on the side panel, then click the Upgrade tab on the top panel.
-
Click System Upgrade.
-
Click on the .bin firmware file for your recorder.
-
Click Start.
17.5.12 Automatic Firmware Upgrades
Firmware upgrades provide enhanced functionality. The system will automatically check for firmware upgrades if it is connected
to the Internet.
To configure automatic firmware upgrade:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click INFORMATION. Click the Update/Reset on the side panel, then click the Upgrade tab on the top panel.
-
Ensure Automatically Check for Updates is checked. If it was previously unchecked, click OK to save changes.
-
Click Check for Updates to check for a newer firmware version.
-
If a newer version is found, click Upgrade Now to upgrade the system.
17.6 Network Settings
Configure general system settings, recording schedule, motion settings, and more.
17.6.1 Selecting DHCP or Static IP Address (TCP/IP)
Configure IP address settings.
To configure IP address settings:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click NETWORK, then click theTCP/IP tab on the side panel.
-
Check DHCP (recommended) to let the system automatically obtain an IP address from the router.
OR
Uncheck DHCP to assign a static IP address (advanced users only).
-
If you uncheck DHCP, configure the following:
-
IP Version: Select IPv4 or IPv6.
-
MAC Address: Enter the MAC address you would like to assign to the system. Make sure that no other device on your network is using the
same MAC address.
-
IP Address: Enter the IP address you would like to assign to the system. Make sure that no other device on your network is using the
same IP address.
-
Subnet Mask: Enter the subnet mask for your network.
-
Default Gateway: Enter the gateway address for your network.
-
Preferred DNS: Enter the address of your primary DNS server.
-
Alternate DNS: Enter the address of your secondary DNS server.
-
Click Apply to save changes.
17.6.2 Configuring System Ports (Connection)
Configure ports used by the system for remote connectivity. If you are using DDNS connectivity, port forwarding is required
for the HTTP Port (default: 80) and TCP (Client) Port (default: 35000).
|
Note
|
Port forwarding is not required unless you are using DDNS for remote access. Using mobile apps does not require port forwarding
or DDNS setup.
|
To configure system ports:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click NETWORK, then click the Connection tab on the side panel.
-
Configure the port numbers as needed.
-
Click Apply to save changes.
|
Note
|
Up to 3 devices may connect to the system at the same time.
|
17.6.3 Configuring Email Alerts
You can configure the system to send out email alerts for motion detection or other events.
|
Note
|
To send out motion detection alerts, you must enable the Send Email option for motion detection on each camera you would to receive alerts from. For details, see
12 Motion Detection
.
|
To configure Email Alerts:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click NETWORK, then click the Email tab on the side panel.
-
Check Enable to enable email notifications.
If you want to use Lorex’s email server (recommended):
-
Under Mail Select, select Lorex Mail to use the Lorex email server to send out alarm notifications. This is the recommended setting.
-
Configure the following:
-
Email Schedule: Configure time periods during which email alerts will be sent.
-
Receiver: Enter the email address that will receive alerts.
-
Sender: Enter the sender’s email address.
-
Subject: Enter the subject line for the email alert.
-
Attachment: Check to include an image attachment of the camera.
|
Note
|
You must enable the Snapshot option for motion detection on each camera you would to receive attachments. For details, see
12 Motion Detection
.
|
-
Interval: Enter the interval between alert emails.
-
Health Enable: Check to enable health check emails. Health check emails will be sent periodically to ensure that the system is functioning
normally. Enter the interval in minutes for health check emails.
-
Click Test to send a test email.
-
Click Apply to save settings.
If you want to use your own email server (advanced):
-
Under Mail Select, select Customize.
-
Configure the following:
-
SMTP Server: Enter the SMTP server address.
-
Port: Enter the port used by the SMTP server.
-
Username: Enter the SMTP user name.
-
Password: Enter the SMTP password.
-
Anonymous: Check if your server supports anonymous log ins. Otherwise, leave this unchecked.
-
Receiver: Enter the email address that will receive alerts.
-
Sender: Enter the sender’s email address.
-
Subject: Enter the subject line for the email alert.
-
Attachment: Check to include an image attachment of the camera.
|
Note
|
You must enable the Snapshot option for motion detection on each camera you would to receive attachments. For details, see
12 Motion Detection
.
|
-
Encrypt Type: Select SSL or TLS if your server uses encryption. Select None if your server does not use encryption.
-
Interval: Enter the interval between alert emails.
-
Health Enable: Check to enable health check emails. Health check emails will be sent periodically to ensure that the system is functioning
normally. Enter the interval in minutes for health check emails.
-
Click Test to send a test email.
-
Click Apply to save settings.
17.6.4 Configuring Switch Settings (Advanced)
Configure the networking settings for the internal PoE switch.
|
CAUTION
|
It is recommended to leave this menu on the default settings. Changing the information in this menu may disrupt the connection
to the cameras.
|
To configure switch settings:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click NETWORK, then click the Switch tab on the side panel.
-
Configure the IP Address, Subnet Mask, and Default Gateway for the internal PoE switch.
-
Click Apply to save changes. The system will restart.
17.6.5 P2P Setting
The P2P Setting menu is used only to enable / disable remote access to the system using a P2P connection.
|
CAUTION
|
P2P connection is the primary method used for remote access to your security system using the
Lorex Home
app. If you disable P2P connectivity, you will only be able to access your system over the Internet using DDNS. See
23 DDNS Setup (Advanced)
for details.
|
To change P2P setting:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click NETWORK, then click the P2P tab on the side panel.
-
Check Enable to use P2P, or uncheck to disable.
-
Click Apply.
17.6.6 Performing Smart Search for Safeguard
Search for safeguard events on a specific channel or the entire system. You can also choose to back up events (USB flash drive
required - not included).
To perform smart search on safeguard events:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click EVENTS. Click the Smart Search tab on the side panel, then in the drop down click the Safeguard tab.
-
Select the channel to search for events from, or select All
-
Choose a start and end time for your search.
-
Under Event Type select either Missing or Left Behind.
-
Click Search. Events that match your search criteria will appear below. If you want to back up events, check the events you want to back
up, then click Export.
17.6.7 Configuring Smart Plan
Select the smart plan feature for your system.
|
Note
|
You can only select one smart plan at a time: Face Detection or Smart Motion, Safeguard, and Active View.
|
To configure your smart plan settings:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click EVENTS. Click the Event Settings tab on the side panel, then in the drop down click the Smart Plan tab.
-
Under Camera, select the channel you would like to configure.
-
Select the smart feature icon
for Face Detection or select the smart feature icon
for Smart Motion, Safeguard, and Active View.
-
When a smart feature icon is enabled, the icon will be blue. Select the individual smart feature icon again to disable. When
a feature has been disabled, the icon will be white.
-
Click Apply to save changes.
17.6.8 Configuring Safeguard
Automatically detect missing or left behind objects within the camera’s field of view by setting designated areas.
To configure safeguard:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click EVENTS, then click the Event Settings tab on the side panel. In the drop down click the Safeguard tab.
-
Under Camera, select the channel you would like to configure.
-
Click on Add to create a new rule.
-
Under Types select Missing for object’s that are missing from the designated area or Left Behind for object’s that have been left behind in the designated area.
-
Once the type of rule has been chosen, click the
Draw icon to edit the rule size and cover area.
-
Select any anchor point of the polygon shape to adjust the rule size and area to filter for Missing or Left Behind objects.
-
Name the rule area.
-
Enter the Period in seconds before an event is triggered.
-
Once done click OK.
-
Click the
Trigger icon to choose which actions to perform when the safeguard rule is triggered.
-
Click Apply to save changes.
17.6.9 Configuring Video Loss Settings
Configure video loss settings and how the system reacts to a video loss event. Video loss means that video from one or more cameras was interrupted or disabled. It could be caused by a number of factors, such as
a loose or damaged connection, loss of power to a camera, or a blocked camera lens.
To configure video loss settings:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click EVENTS. Click the Event Settings tab on the side panel, then in the drop-down click Motion. On the top panel click Video Loss.
-
Under Camera, select the channel you would like to configure.
-
Check Enable to enable video loss events for the selected channel.
-
Configure the following to customize settings for video loss events:
-
Schedule: Click Set to configure a schedule for video loss events. It is recommended to leave this on the default setting, so you can be alerted
at any time one of your cameras loses video.
-
Show Message: Check to show a popup message on the monitor if one of your cameras loses video.
-
Send Email: Check to enable email alerts. You must configure email alerts before you will be able to receive them (see
17.6.3 Configuring Email Alerts
).
-
Record Channel: Click the checkbox to enable video recording when video loss occurs. Click Set to select which channels the system will record when video loss occurs on the currently selected channel.
-
PTZ Activation: Check to enable PTZ actions when video loss occurs (PTZ camera required; not included). Click Set to select which PTZ actions will be taken by each camera.
-
Post_REC: Enter the number of seconds the system will record after video loss occurs.
-
Sequence: Check to enable a custom sequence mode when motion is detected on the selected channel. Click Set to select which channels you would like to display in the custom sequence mode.
-
Buzzer: Check to enable the system buzzer when video loss occurs on the currently selected channel.
-
Click Apply to save changes.
17.6.10 Configuring Hard Drive Warnings
Hard drive warnings will notify you if an issue is detected with the hard drive.
To configure hard drive warnings:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click EVENTS. Click the Warning tab on the side panel, then click the HDD tab on the top panel.
-
Under Event Type, select the hard drive event you would like to configure. Check Enable to activate the selected warning.
-
No Disk: No hard drive detected.
-
Disk Error: A hard drive error has been detected.
-
Disk Full: The hard drive is full or almost full. You can enter the percentage of disk space remaining that will trigger a warning under
Less Than (e.g. when less than 10% of the hard drive is empty, trigger a warning). Disk Full warnings will not occur if overwrite is
enabled.
-
All: Configure warnings for all hard drive events.
-
Configure the responses the system will take when the selected event occurs:
-
Show Message: Show a popup message on the monitor.
-
Send Email: Check to enable email alerts. You must configure email alerts before you will be able to receive them (see
17.6.3 Configuring Email Alerts
).
-
Buzzer: Check to activate the system buzzer.
-
Click Apply to save changes.
17.6.11 Configuring Network Warnings
Network warnings will notify you if there your system loses connection to the Internet or local network or if there is an
issue on your network.
To configure network warnings:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click EVENTS. Click the Warning tab on the side panel, then click the Network tab on the top panel.
-
Under Event Type, select the event type you would like to configure. Check Enable to activate the selected warning.
-
Net Disconnection: The system has lost connection to the network.
-
IP Conflict: More than one device on your network has the same IP address.
-
MAC Conflict: More than one device on your network has the same MAC address.
-
All: Configure responses for all network events.
-
Configure the following for the selected event type:
-
Show Message: Check to show a popup message when the selected event occurs.
-
Send Email: Check to enable email alerts. You must configure email alerts before you will be able to receive them (see
17.6.3 Configuring Email Alerts
).
-
Buzzer: Check to activate the system buzzer.
-
Click Apply to save changes.
17.6.12 Searching Event Logs
Search all channels for events, including motion detection and video loss.
To access the log menu:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click EVENTS, then click the Event Log tab on the side panel.
-
Select an event type to search for.
-
Enter a start and end time for your search.
-
Click Search.
-
Events that match your search criteria are displayed:
-
The Event column is formatted to show [Event Type]: [Channel Number]>.
-
Click Details to see more information on the selected event.
-
Smart Motion events have more options than other events. You can view the event by clicking the icon
in the Playback column, or back up the video clip to a USB flash drive (not included) by clicking Backup.
17.6.13 Configuring Pre-Recording
The system can pre-record video when motion detection events occur. This will ensure that the system records the entire event
when motion is detected. By default, the system pre-records 4 seconds of video every time motion is detected.
|
Note
|
Ensure you have set your preferences for motion detection (see
12 Motion Detection
for details).
|
To configure pre-recording:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click STORAGE. Click the Schedule tab on the side panel, then click the Record tab on the top panel.
-
Under Channel, select the camera you would like to configure or select All.
-
Under PreRecord, select the duration for pre-recording.
-
Click Apply to save settings.
17.6.15 Configuring Hard Drive Type
The system supports the following hard drive types:
-
Read/Write: Normal recording hard drive.
-
Read-Only: The system can playback data from this hard drive, but it will not record to it.
To set the hard drive type:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click STORAGE, then click the HDD Manager tab on the side panel.
-
Select the hard drive type under the Type column next to the hard drive you would like to configure.
-
Click Apply to save changes. The system will restart to complete this operation.
17.6.16 Configuring Record Estimate (Recording Calculator)
Use the recording calculator to get an estimate of your maximum recording time in days for the installed hard drive, or how
much hard drive space would be required to retain a specific amount of days.
To obtain a recording estimate:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click STORAGE, then click the Record Estimate tab on the side panel.
-
Select Recording Days for the total number of days worth of recordings your hard drive can store, or select Disk Requirement for the total storage needed to record for a specific number of days
-
For Recording Days mode, click Select to choose your hard drive from a list to output the total number of days your hard drive can store. For Disk Requirement mode, enter a number of days to output the total amount of storage required.
-
Click Apply to save settings.
17.6.17 FTP (Advanced)
Send recordings and/or snapshots to an FTP server.
To configure FTP settings:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click STORAGE, then click the FTP tab on the side panel.
-
Check Enable to allow FTP connection, and select either FTP or SFTP depending on your configuration.
-
Configure the following:
-
Server: Enter the FTP server’s address.
-
Port: Enter the FTP port.
-
Username: Enter your FTP username.
-
Password: Enter your FTP password.
-
Anonymous: Enable if your FTP server supports anonymous login.
-
Remote Directory: Enter the directory to save recordings and/or snapshots to.
-
File Length: Enter the recording file length in minutes.
-
Channel: Select a channel to set FTP recording preferences for.
-
Week: Select a day of the week to configure FTP recording settings for, or select All to apply to all days of the week.
-
Image Upload Interval: Enter the interval between snapshots in seconds.
-
Channel: Select a channel to set the snapshot preference for.
-
Click Apply.
17.6.18 Configuring General System Settings
Configure miscellaneous system settings.
To configure general settings:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click SYSTEM. Click the General tab on the side panel, then click the General tab on the top panel.
-
Configure the following:
-
Device Model: The camera model name.
-
Device No.: Not supported.
-
Language: Set the system languages. Available options are English, French, and Spanish.
-
Video Standard: Select NTSC (North America) or PAL (Europe).
-
HDD Full: Select Overwrite for the system to overwrite the oldest recordings when the hard drive is full or select Stop Record for the system to stop recording when the hard drive is full.
-
Pack Duration: Set the length of time (in minutes) for video files saved to the hard drive. For example, if set to 30 minutes, the system
will create a new video file for every 30 minutes of continuous recording.
-
Instant Playback: Select the amount of time (in minutes) the system will go back when instant playback is activated in live view.
-
Auto Logout: Select the idle time (in minutes) before the system will logout the current user.
-
IPC Time Sync: Check to enable.
-
IPC Time Sync Period: Select how often (in hours) the NVR will update the time on the IP cameras.
-
Navigation Bar: Check to enable the Navigation Bar that comes up when you left click in live view.
-
Mouse Sensitivity: Use the slider to adjust the mouse speed.
-
Click Apply to save changes.
17.6.19 Configuring Holidays
You can set certain days as holidays. Holidays have a special recording schedule.
To configure holidays:
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click SYSTEM. Click the General tab on the side panel, then click the Holiday tab on the top panel.
-
Click Add New Holidays.
-
Configure the following:
-
Holiday Name: Enter a name for this holiday.
-
Repeat Mode: Select Once for the holiday to occur only this year or Always for the holiday to be repeated each year.
-
Holiday Range: Select Date to select a specific date, or select Week to select holidays based on which week they fall on.
-
Start Time/End Time: Enter when the date for when the holiday starts and ends.
-
Click Add More. Now that you have added a holiday, an extra holiday setting is added to the recording schedule.
|
Note
|
You cannot delete holidays, but you can disable them by selecting Off under the Status drop-down, then click Apply.
|
17.6.20 Configuring IP Filter
Configure permissions for external IP addresses attempting to access the unit.
-
From the Live View display, right-click to open the Quick Menu, then click Main Menu.
-
Click SYSTEM, then click the Security tab on the side panel. Click the Firewall tab on the top panel.
-
Check Enable.
-
Select Trusted Sites to add IP addresses or ranges that are permitted to access the recorder, or select Blocked Sites to add IP addresses or ranges that are not permitted to access the recorder.
-
Click Add to enter an IP address or range.
-
Click Apply when finished.