4 Basic System Setup
4.1 STEP 1: Connect cameras
|
Note
|
This step is for verification of the camera image only. It is recommended to connect cameras to a nearby power adapter for
this step. The Lorex Setup Wizard that runs at startup will assist you in naming and organizing your cameras, so it is also
recommended to leave cameras connected until the wizard asks you to install cameras in their permanent mounting location.
|
Option 1: Direct Connection to NVR
Test your cameras prior to selecting a permanent mounting location by temporarily connecting the cameras and cables to your
recorder. Connect the cameras to the recorder using the RJ45 Ethernet extension cables provided with your cameras.
Option 2: Connect Cameras to Local Network
|
Note
|
Before selecting a permanent mounting location for your cameras, see
5 Camera Installation
for important notes and installation tips.
|
4.2 STEP 2: Connect router
Connect the recorder to your router using the included Ethernet cable.
|
Note
|
To receive automatic firmware updates and enable remote viewing with mobile apps, a high speed Internet connection is required
(minimum upload speed of 5Mbps required for 4K viewing; 3.5Mbps for lower resolutions). All other system features can be used
without an Internet connection.
|
4.3 STEP 3: Connect mouse
Connect the included mouse to a USB port on the recorder.
4.4 STEP 4: Connect monitor
Connect the recorder to a monitor using the included HDMI cable (supports up to 4K resolution).
OR
Connect the recorder to a monitor using a VGA cable (not included - supports up to 1080p resolution).
|
CAUTION
|
|
4.5 STEP 5: Connect power
Use the included power adapter to connect the recorder to a nearby outlet.
Turn on the power switch on the back of the unit to power up the recorder.
4.6 STEP 6: Upgrade Firmware to Latest Version (If Available)
If a firmware upgrade is available, you will be asked to install it once the system starts up. It is recommended to upgrade
your system firmware and client software or mobile apps to the latest version to ensure remote connectivity to the system
and support newly-developed features.
|
Note
|
You must connect your recorder to a router with Internet access in order to get automatic firmware upgrades.
|
If a firmware upgrade is available:
-
After startup, a notification will appear asking you to upgrade the firmware. Click OK to upgrade.
-
Enter the system user name (default: admin) and your secure password, then click OK. Wait for the firmware update to complete. The system will restart once the firmware has been upgraded.
|
CAUTION
|
DO NOT POWER OFF THE SYSTEM OR DISCONNECT THE POWER CABLE DURING FIRMWARE INSTALLATION.
|
4.7 Quick Access to System Information
Perform one of the following actions to bring up the system information window. This window contains vital system information
including the model number, serial number, and device ID.
|
Note
|
The QR code shown on this screen can be scanned during mobile setup to enter the system’s device ID.
|
To quickly open a window that displays important system information:
-
From the Live View display, right-click to open the Quick Menu, then click Info.
OR
-
Press the front panel button on the recorder.
|
Note
|
Do not press and hold the button. The front panel button doubles as a panic button that activates warning lights and sirens
for deterrence cameras if held for 3 seconds.
|
4.8 Connecting Cameras to the Local Area Network (LAN)
For flexibility, you may also connect IP cameras to the same Local Area Network (LAN) as the NVR instead of connecting them
directly to NVR. This is accomplished by connecting the cameras to the same router as the NVR.
For these installations, an external PoE switch (sold separately) or power adapter (sold separately) must be used to provide
power to each IP camera. You also must add the cameras on the NVR before they will show a picture on the monitor or be recorded
by the NVR.
Follow the steps below to connect the cameras to the NVR over the LAN.
|
Note
|
|
-
Connect an Ethernet cable from the LAN port on an external PoE switch (sold separately on
lorex.com
) to your router using a CAT5e or higher Ethernet cable. Connect the power cable to the PoE switch and to a power outlet or
surge protector.
|
Note
|
Terminology may vary depending on the model of PoE switch you have.
|
-
Connect the IP cameras to the PoE switch using the Ethernet extension cables. The PoE switch will provide power and video
transmission the same way as your NVR.
-
Connect each camera to a compatible power adapter (check your camera documentation at
lorex.com
for compatible power adapters for your cameras).
-
Connect the camera to your router using a CAT5e or higher Ethernet cable.
Step 2 of 2: Add the cameras to your NVR:
-
Right-click and select Camera Registration.
-
Click Device Search. The system searches the network for compatible cameras.
|
Note
|
It may take a few minutes after you power up IP cameras for them to appear in your search.
|
-
Check the camera(s) you would like to add.
-
Click Add. The Status indicator turns green to show the camera is successfully connected.
|
Note
|
You can also add a camera to a specific channel by hovering the mouse over an empty channel in split-screen view and clicking
. Double-click the camera you would like to add, then right-click to exit.
|