Buy Online or Call 1-888-425-6739 | 8:30 AM - 7 PM EST | 7 Days a Week

LZC7092B PTZ Camera - Frequently Asked Questions

Relevant Models / Series: LZC7092B

 

Q: Why is the image unclear when the camera is pointed at certain angles?

A: This PTZ camera is designed to tilt up and down within a range of 160°. Tilting less than 10° or greater than 170° away from the camera base may cause the image to become slightly unclear. It is recommended to install the camera as high up as possible.

If the image becomes unclear, use the DVR controls to tilt the camera between 10° and 170°. The camera's tilt angle appears on the monitor when it moves as shown below.

-

Q: Can I extend the cable beyond the supplied 100ft extension cable?

A: Yes, the video cable and RS485 PTZ control cables can be extended up to 350ft (106m) from the camera. However, due to the high power requirements of this camera, the power cable can not be extended further than 100ft (see "Power" section below for more details).

To extend the video cable and RS485 PTZ control cables beyond 100ft:

  • Video Cable: Use RG59 coaxial extension cables. It is recommended to use video cables with the following specification: RG59U 95% Braid 20AWG or better. Up to 250ft of additional video cabling may be added to the supplied 100ft cable.

  • RS485 PTZ Controls: Use a pair of 24-gauge wires. Use the included RS485 connection terminals to connect RS485 wires to each other. See images below for details.

    Loosen screw terminals with a
    screwdriver
    Insert 24-gauge wires and tighten screw terminals to secure wires

  • Power: Because this is a high-powered PTZ camera, the power cable cannot be extended beyond 100ft. You may connect the included power adapter directly to the camera’s power connector and plug the adapter into a power outlet near the camera. Or, you may connect the power adapter to the end of the 100ft cable.

 

Scenario 1: Connect power adapter near camera
1. Connect power adapter to the camera cable and connect to a nearby power outlet.
2. Connect the camera to the BNC and RS485 connectors on the included 100ft extension cable.
3. Connect additional extension cables to the included extension cable.

 

Scenario 2: Connect power adapter at the end of the included extension cable
1. Connect camera cables to the included extension cable.
2. Connect power adapter to the included extension cable on the side away from the camera.
3. Connect additional extension cables to the included extension cable.

Q: How do I connect the PTZ camera to Eco DVRs?

A: Follow the steps below:

  1. Ensure the RS485 wires are connected correctly to the RS485+ and RS485- ports on the DVR and that the video cable is connected.
  2. On the DVR, right-click with the mouse to open the Menu Bar and click the Main Menu button ().
  3. Click Device and select the PTZ tab.


     
  4. Configure the following:
    • Channel: Select the channel the PTZ camera is connected to.
    • Protocol: Select the protocol (default: Pelco-D).
    • Baud rate: Select the camera’s baud rate (default: 9600).
    • Data Bit: Select 8.
    • Stop Bit: Select 1.
    • Parity: Select None.
    • Cruise: Select Enable to enable PTZ cruise.
    • Address: Enter the camera’s ID (default: 001).
  5. Click Apply to save your settings.

To control the PTZ camera:

  • Select the camera in live view, right-click, and click the button on the Menu Bar. Enter the DVR password (default: 000000). PTZ controls appear. See the DVR instruction manual for more details.

Q: How to I connect the PTZ camera to Edge DVRs?

A: Follow the steps below:

  1. Ensure the RS485 wires are connected correctly to the RS485+ and RS485- ports on the DVR and that the video cable is connected.
  2. Click then . Click RS485. The RS485 Menu opens.


     
  3. Click Baud Rate and scroll up/down to select the camera's baud rate (default: 9600).
  4. Click PTZ Camera Setup. Select the channel your PTZ camera is connected to. The PTZ Camera Setup Menu opens.


     
  5. Click Camera ID and scroll up/down to select the camera's ID (default: 1).
  6. Click Control Enable and select O to enable PTZ controls for the selected channel.
  7. Click Protocol and scroll up/down to select the PTZ protocol for your camera (default: Pelco-D).
  8. Right-click until you have exited all menus to save your changes.

To control the PTZ camera:

  • Select the camera in live view and click the button on the Menu Bar. PTZ controls appear. See the DVR instruction manual for more details.
Last Updated: 5/26/2014